Step 15: Trim, trim, trim, trim, trim....

God it never ends.

Finish-work.

I got a new airbrush - loving it so far.  Tried out some stencils I picked up from AC Moore to see how it will all come together.  Don't worry the panel hasn't finished being painted red yet, the stenciling will end up symmetrical and AWESOME.

Honestly I'm looking forward to the artwork side of this.  The main project build has been engrossing, but hard work - more engineering that artistry.

Also the interior needs a lot more finish-work, but all in good time. :D

This pic shows a mock up of the bedroom arch (which should have been installed before the exterior cover).

These 10' long paneled boards (that I'm calling waist-boards) will run alongside and above the base of the caravan, and sandwich the end of the tarp neatly to the side of the caravan.  It's also a way of increasing the visible sideboard, making it appear considerably more aesthetically appealing from the side. 

Step 14: Floors and more paint

Floors got some varnish, which helped stop marking them up every-time I was up and down installing something.

More paint got laid down - I switched to the spray-gun for cutting in and just a small 6" foam roller for the face panels.  It goes on quick.

Then I set about waterproofing the front face.  This face is especially important to waterproof as it's facing into the wind when being towed at 65 miles an hour in a rainstorm.  The front edge will catch all that rain and wind and, at that speed, it's like directly pressure-washing the front. 

Waterproofing the front doors is going to suck.

Step 13: Insulation

I moved a bit quick here and installed the fabric sooner than I should have.  It's probably not going to be worth a redo - but time will tell.

Over the fabric I installed some reflective bubblewrap, three layers in fact!  It helps.  It's also quite pricey.  I bought too much, and just used it all instead of returning some.  A single layer is really all that is needed.

Next time (haha) I think it would be better to cut the insulation to size, and contact glue the fabric to it, installing it all in one go.  As is the fabric sags slightly in each panel.  It's not a problem but it still bothers me!

Step 12: Paint!

It's going to be red, apparently.

I took advantage of some dry weather and some readily available assistance (my ridiculously beautiful spouse) to uncover and start installing the fabric liner.  This was a turning point in construction as the whole build started to get delicate - I couldn't just sand willi-nilly now and had to start minding my mess everywhere.  This slowed me down slightly :)

.

Step 11: A teardrop camper?

When fitting the panels for the front overhang I stumbled on these great shapes.  Next time I build one of these (haha) I might consider this, it's really very pretty.

I dry fit the door panels I had glued up - for me this was the first time it really felt like it might actually work!

Step 10: Some cabinetry and carpentry!

A lot of cleanup happened at this point, and lots of mockup stuff, but I settled on how the cabinets and benchs were going to end up.
The areas behind and on top of the benches are sealed so they can be used as storage/shelves.
The bench surfaces were made of out two 'spare' staircase risers I had floating around, as they are nice and thick and already rounded on one edge.

The electrical panels in the right-hand cabinet are overkill but since I had em from the boat project I decided to use em.

Lastly I laid out the floorboards.

Step 9: Wood Panelling?

This was a late-in-the-game design change because I spotted these engineered plywood 1/4" panels and really liked working with them.  They bend really well, and look great and add some much needed structure to wall areas that may be leaned on. 

These pics show 2' wide panels installed over the stringers on sensitive areas.  This plywood is only $15 for each 4x8 sheet (I used most of 3) so didn't break the budget (much).

You can also see in these pics I've fleshed out the cabinets at the entrance as well as added surfaces ot the benches.  These were all temporary mock ups, but made it much easier to work in there.